Cooler Master Box Lite 5 RGB ATX Mid-Tower w/ Front DarkMirror Panel, 3 Customize Color Trims, Tempered Glass Side Panel & 3x 120mm

This case looks so cool. I used it recently to build my wife a pc for casual gaming and programming. It turned out amazing! Even though there were a few things I didn't like I was not disappointed. Tight fit for cables compared to the Cooler Master MasterBox 5 Mid tower I have another build in its a bight tighter but I managed. The noise is almost unnoticeable but that's also attributed to the quiet GPU and tough power grand PSU I have in the pc, but all together is so quiet. And the tinted front and tempered glass give it a look, unlike almost any other case.

As a whole, the case is high quality with beautiful appearance. Though glass panel you can clearly look into your motherboard, and the front RGB fan is awesome. However, pay attention to the heat problem. The front panel has little hole, so the three front RGB fan actually contribute little to cooling. There is NO TOP FAN on the top of the case. Also there is no air outlet on the top. The top side is only a steel panel. So If your CPU is stressfully hot, you should consider buy a case with better air flue.

The case looks fantastic. That being said...youll need to have a rgb header on youre mobo or buy a controller for the rgb effects. Without the header or controller you will be left with red or blue (wasnt an issue for me die to already have a rgb header). The side pannel is lovely i enjoy the tinted look. The front cover is a tinted plastic looks very nice as well. There is VERY limited air flow. Tiny space on tmthe top of the front panel and bottom. There is no place more fans or closed loop cpu cooler on the top. O ended up modding my case for more front air flow ( i drilled holes on the front panel) it helped dramatically. I did a very beat job so it dose not look bad what so ever. I also modded the top of the case so i could fit a closed loop water cooler. Without nodding the case ill list pros and cons.Pros:Acrillic side pannel is lovely and rare on a case for this cost.3 rgb fans ( not the prettiest fans but nice non the less)Large case can fit any and all components(minus a cpu liquid cooler)You can change small hits of the from panel (they include info for 3d printing youre own)Lots of room for cable managment3.0 usb header in the frontCons:Airflow air flow airflow. 3 front case fans but very minimum open space to intake air.No room for fans or aio on the top.A very nitpicky one the front is a finger print magnet!Modding the case wasnt to bad i just used tape and a drill for more airflow the front and a knife/ fine grit sand paper to Smith evrythong out.For the top I used a dremmel to cut a hole and bought a 3rd party dust filter and aio top cover. And a drill for screw holes.

Very good case for a first build!Pros:Ok sized, not big enough to have a watercooling loop in but plenty big for the average build.Decent-ish airflow, it's 50/50 with the front being 90% plastic and only one exhaust fan in the rear, but with the back being 75% vented as well it allows a decent amount of air exchange.Good looking, 3 120mm RGB fans make this case look good and light up a majority of the case on their own.Great price, for it's price point, it functions well and does it's job, all while looking fairly decentCons:Very poor cable management, the back panel has about maybe 1/3" for running cables, which means it bows out a bit if you don't run them all perfectly flat.Extremely limited radiator placement options, with only space for a 120mm in the back and up to a 360mm in the front, this case is very limited on radiator space.50/50 airflow, this case was iffy on airflow, I could see if it had a mesh front it would be better, but again with 90% of the front in plastic, it's just not as good.This case helped me learn the pros and cons of cases and I have since stuck with Cooler Master and gotten an H500P which is amazing and keeps my build below 50°c at maximum strain, even without the additional mesh front, which I plan to get eventually.All in all, this is a good case, whether it be for a starter or just a budget build. Definitely would recommend for either of those situations.